IEC 62484Specifies the operational and performance requirements for spectroscopy-based portal monitors used for the detection and identification of illicit trafficking of radioactive material.
IEC 62489-2IEC 62489-2:2014 applies to audio-frequency induction-loop systems for assisted hearing. It may also be applied to such systems used for other purposes, as far as it is applicable. The standard is intended for assessment of human exposure to low-frequency magnetic fields produced by the(...)
IEC 62495IEC 62495:2011(E) is applicable to the radiological safety of portable handheld X-ray fluorescence (XRF) analysis equipment utilizing a miniature X-ray tube as the source of ionizing radiation for industrial applications. Establishes performance specifications for general radiation,(...)
IEC 62501IEC 62501:2009+A1:2014 applies to self-commutated converter valves, for use in a three-phase bridge voltage sourced converter (VSC) for high voltage d.c. power transmission or as part of a back-to-back link. It is restricted to electrical type and production tests.
IEC 62523Applies to radiographic inspection systems with photon radiation energy of at least 500 keV for inspection of cargo, vehicles and cargo containers.
IEC 62533Applies to hand-held instruments used for the detection and localization of radioactive photon emitting materials.
IEC 62534Applies to hand-held instruments used for the detection and localization of neutron emitting radioactive material.
IEC 62542Specifies generic terms and definitions that are related to environmental standardization within the IEC. It serves as a glossary of terminology to be considered for environmental aspects of relevant work in IEC.
IEC 62566IEC 62566:2012 provides requirements for achieving highly reliable "HDL-Programmed Devices" (HPD), for use in I&C systems of nuclear power plants performing functions of safety category A as defined by IEC 61226.
IEC 62577Applies to a single stand-alone broadcast transmitter operating in the frequency range 30 MHz to 40 GHz when put on the market. The objective of the standard is to specify, for such equipment operating in typical conditions, the method for assessment of compliance distances according to the(...)
IEC 62598IEC 62598:2011 applies to the manufacture and installation of electrical measuring systems and instruments utilizing radioactive sources (radiometric gauges, hereinafter called gauges). It also applies to source housings intended for use in the aforementioned measuring systems.
IEC 62599-1Specifies environmental test methods to be used for testing the system components of the following alarm systems, intended for use in and around buildings
IEC 62599-2Immunity requirements applies to the components of the following alarm systems, intended for use in and around buildings in residential, commercial, light industrial and industrial environments
IEC 62618Standard establishes performance requirements, provides examples of acceptable test methods and specifies general characteristics, general test conditions, radiological, environmental, mechanical and electromagnetic characteristics that are used to determine if an instrument meets the(...)
IEC 62631This IEC standard describes dielectric and resistive properties of solid insulating materials.
IEC 62642-1Specifies the requirements for intrusion and hold-up alarm systems (I&HAS) installed in buildings using specific or non-specific wired interconnections or wire-free interconnections
IEC 62642-2-2Is for passive infrared detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
IEC 62642-2-3Is for microwave detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
IEC 62642-2-4Is for combined passive infrared and microwave detectors installed in buildings and provides for security Grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
IEC 62642-2-5Is for combined passive infrared and ultrasonic detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
