IEC 62047-21Specifies the determination of Poisson’s ratio from the test results obtained by the application of uniaxial and biaxial loads to thin-film micro-electromechanical systems (MEMS) materials with lengths and widths less than 10 mm and thicknesses less than 10 µm.
IEC 62047-22Specifies a tensile test method to measure electromechanical properties of conductive thin micro-electromechanical systems (MEMS) materials bonded on non-conductive flexible substrates.
IEC 62056-21Describes hardware and protocol specifications for local meter data exchange. In such systems, a hand-held unit (HHU) or a unit with equivalent functions is connected to a tariff device or a group of devices.
IEC 62056-42Specifies the physical layer services and protocols within the Companion Specification for Energy Metering (COSEM) three-layer connection oriented profile for asynchronous data communication.
IEC 62056-46Specifies the data link layer for connection-oriented, HDLC-based, asynchronous communication profile.
IEC 62056-47Specifies the transport layers for COSEM communication profiles for use on IPv4 networks. These communication profiles contain a connection-less and a connection-oriented transport layer, providing OSI-style services to the service user COSEM application layer. The connection-less transport(...)
IEC 62061Specifies requirements and makes recommendations for the design, integration and validation of safety-related electrical, electronic and programmable electronic control systems (SRECS) for machines (see Notes 1 and 2).
IEC 62088Establishes standard test procedures for photodiodes used in scintillation detectors and defines the parameters which shall be provided by the supplier for each type of photodiode.
IEC 62089Establishes standard methods for calibration and use of alpha/beta gas proportional counters, including measurement of their characteristics. Applies to alpha/beta gas proportional counting systems used for the determination of the alpha-ray or beta-ray emission rates of radionuclides in(...)
IEC 62093Establishes requirements for the design qualification of balance-of-system (BOS) components used in terrestrial photovoltaic systems. Is suitable for operation in indoor, conditioned or unconditioned; or outdoor in general open-air climates, protected or unprotected. Is written for dedicated(...)
IEC 62097IEC 62097:2009 is applicable to the assessment of the efficiency and performance of prototype hydraulic machine from model test results, with consideration of scale effect including the effect of surface roughness.
IEC 62108Specifies the minimum requirements for the design qualification and type approval of concentrator photovoltaic modules and assemblies suitable for long-term operation in general open-air climates.
IEC 62109-1IEC 62109-1:2010(E) applies to the power conversion equipment (PCE) for use in photovoltaic systems where a uniform technical level with respect to safety is necessary. Defines the minimum requirements for the design and manufacture of PCE for protection against electric shock, energy, fire,(...)
IEC 62109-2IEC 62109-2:2011 covers the particular safety requirements relevant to d.c. to a.c. inverter products as well as products that have or perform inverter functions in addition to other functions, where the inverter is intended for use in photovoltaic power systems. Inverters covered by this(...)
IEC 62115Deals with the safety of toys that have at least one function dependent on electricity. Examples of toys within the scope of this standard are: constructional sets; experimental sets; functional toys (having a function similar to an appliance or installation used by adults) and video toys(...)
IEC 62116IEC 62116:2014 provides a test procedure to evaluate the performance of islanding prevention measures used with utility-interconnected PV systems. This standard describes a guideline for testing the performance of automatic islanding prevention measures installed in or with single or(...)
IEC 62117Gives requirements for instrumentation to monitor core cooling for safe operation of PWRs during cold shutdown operations when the coolant temperature is below 100 °C. Summarizes good international practices to be used when designing new or upgrading existing PWR core cooling monitors.
IEC 62124Verifies system design and performance of stand-alone photovoltaic systems. The performance test consists of a check of the functionality, the autonomy and ability to recover after periods of low state-of-charge of the battery, and hence gives reasonable assurance that the system will not fail(...)
IEC 62138Provides requirements for the software of computer-based I&C systems performing functions of safety category B or C as defined by IEC 61226.
IEC 62192Covers insulating ropes that are utilized during live working procedures in contact with parts of installations operating at voltages up to and including 800 kV r.m.s.
