IEC 60839-7-6Specifies the requirements for standard interfaces employing ITU-T V.24/V.28 signalling for communications between the control and indicating equipment of an alarm system and transmission equipment used for remote communications, where the transmission equipment is general purpose equipment.(...)
IEC 60839-7-7Specifies the requirements for standard interfaces between the control and indicating equipment (CIE) of an alarm system and an alarm system transceiver where the alarm system transceiver is intended to plug into a standard space inside the CIE of the alarm system.
IEC 60839-7-11Specifies the requirements for standard interfaces between the Public Switched Telephone Network (PSTN) and alarm system transceivers. Specifies a 1 200 baud interface using ITU-T Recommendation V.23.
IEC 60839-7-12Specifies the requirements for standard interfaces between the alarm system transceivers and transmission network where both form part of a dedicated channel alarm transmission system as defined in IEC 60839-5-4.
IEC 60839-7-20Specifies the requirements for standard interfaces between the terminal transceiver of an alarm transmission system and the annunciation equipment. Employs signalling in accordance with ITU-T Recommendation V.24/V.28.
IEC 60839-10-1Specifies requirements and test methods for vehicle security alarm systems in tended for installation within vehicles used for the carriage of passengers and having not more than eight seats in addition to the driver's seat.
IEC 60839-11-1Specifies the minimum functionality, performance requirements and test methods for electronic access control systems and components used for physical access (entry and exit) in and around buildings and protected areas.
IEC 60846-1Specifies the design requirements and the performance characteristics of dose equivalent (rate) meters intended for the determination of ambient dose equivalent (rate) and directional dose equivalent (rate) as defined in ICRU Report 47.
IEC 60846-2Applies to portable or transportable dose equivalent (rate) meters and/or monitors for the measurement of ambient and/or directional dose equivalent (rate) from external beta, X and gamma radiation during emergency situations.
IEC 60855-1Applicable to insulating foam-filled tubes and solid rods, of a circular cross-section, made of synthetic materials and intended to be used for the manufacture and construction of tools and equipment for carrying out live work on electrical systems operating at voltages above 1 kV.
IEC 60860Applies to equipment intended to detect ionizing radiation from, and provide warning of, a criticality accident. Specifies the general characteristics, operating characteristics, electrical, mechanical, safety and environmental characteristics, test procedures and documentation.
IEC 60861Defines technical requirements for equipment for monitoring of alpha-, beta- or gamma-emitting radionuclides in liquid effluents and surface waters, provides general guidance as to the possible detection capability of such equipment and indicates when and where its uses may be practicable.
IEC 60880Provides requirements for the software of computer-based instrumentation and control (I&C) systems of nuclear power plants performing functions of safety category A as defined by IEC 61226. Provides requirements for the purpose of achieving highly reliable software.
IEC 60891IEC 60891:2009 defines procedures to be followed for temperature and irradiance corrections to the measured I-V (current-voltage) characteristics of photovoltaic devices. It also defines the procedures used to determine factors relevant for these corrections.
IEC 60895Applicable to conductive clothing, either assembled from component parts or forming a single complete clothing, worn by (electrically) skilled persons during live working (especially bare-hand working) at a nominal power system voltage up to 800 kV a.c. and ±600 kV d.c. It is applicable to(...)
IEC 60900Applicable to insulated and insulating hand tools used for working live or close to live parts at nominal voltages up to 1 000 V a.c. and 1 500 V d.c. This third edition cancels and replaces the second edition, published in 2004.
IEC 60903This standard is applicable to: - insulating gloves and mitts which should normally be used in conjunction with leather protector gloves worn over the insulating gloves to provide mechanical protection; - insulating gloves and mitts usable without over-gloves for mechanical protection.
IEC 60904-1Describes procedures for the measurement of current-voltage characteristics of photovoltaic devices in natural or simulated sunlight. Lays down basic requirements for the measurement, defines procedures for different measuring techniques in use and shows practices for minimising measurement(...)
IEC 60904-2Gives requirements for the classification, selection, packaging, marking, calibration and care of reference solar devices. Covers solar reference devices used to determine the electrical performance of solar cells, modules and arrays under natural and simulated sunlight.
IEC 60904-3IEC 60904-3:2008 describes basic measurement principles for determining the electrical output of PV devices. The principles given in this standard are designed to relate the performance rating of PV devices to a common reference terrestrial solar spectral irradiance distribution.
