IEC 61400-25-6IEC 61400-25-6:2010(E) specifies the information models related to condition monitoring for wind power plants and the information exchange of data values related to these models.
IEC 61427-1IEC 61427-1:2013 is part of a series which gives general information relating to the requirements for the secondary batteries used in photovoltaic energy systems (PVES) and to the typical methods of test used for the verification of battery performances.
IEC 61435IEC 61435:2013(E) is applicable to high-purity germanium crystals used for radiation detectors for gamma-rays and X-rays. Such germanium is monocrystalline and has a net concentration of fewer than 1011 electrically active impurity centers per cm3. This International Standard specifies(...)
IEC 61453Specifies methods of calibration and routine tests of scintillation detector systems for the measurement of gamma-ray energies and emission rates of radionuclides and the assay of radioactivity. Is applicable to scintillation detector systems based on inorganic scintillators for photon measurements.
IEC 61468Applies to in-core neutron detectors and instrumentation, which are designed for purposes important to safety, such as protection, control and information. Gives requirements, recommendations and guidance on selection of the type and characteristics of self powered neutron detectors used in(...)
IEC 61472Describes a method for calculating the minimum approach distances for live working, at maximum voltages between 72,5 kV and 800 kV. This standard addresses system overvoltages and the working air distances or tool insulation between parts and/or workers at different electric potentials.
IEC 61477Gives the minimum requirements relative to specification, manufacture, selection, application and maintenance of tools, devices and equipment for live working. It provides the type of information which is useful to skilled persons in order to make the use of tools, devices and equipment safer.
IEC 61478Is applicable to fully insulating spliced or hook ladders with extension or having a combination of insulating and conductive sections and used for live working on a.c. or d.c. electrical installations at 1 000 V and above for a.c. and 1 500 V and above for d.c. This standard concerns only(...)
IEC 61479Is applicable to flexible insulating covers (line hoses) for the protection of workers from accidental contact with live or earthed electrical conductors and for the avoidance of short circuits during live working.
IEC 61481Is applicable to portable phase comparators with or without a built-in power source to be used on electrical systems for voltages from 1 kV to 36 kV a.c. and frequencies from 50 Hz to 60 Hz. This standard is applicable to two-pole phase comparators having a connecting lead between them,(...)
IEC 61482-1-1Specifies test methods to measure the arc thermal performance value of materials intended for use in heat- and flame-resistant clothing for workers exposed to the thermal effects of electric arcs and the function of garments using these materials.
IEC 61482-1-2This part of IEC 61482 specifies methods to test material and garments intended for use in heat- and flame-resistant clothing for workers exposed to electric arcs. In contrast to the test methods in IEC 61482-1-1 a directed and constrained electric arc in a low voltage circuit is used to(...)
IEC 61482-2Applicable to protective clothing used in work if there is an electric arc hazard. Specifies requirements and test methods applicable to materials and garments for protective clothing for electrical workers against the thermal hazards of an electric arc based on: relevant general properties of(...)
IEC 61496-1Specifies general requirements for the design, construction and testing of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety related system.
IEC 61496-2Specifies requirements for the design, construction and testing of electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety-related system, employing active opto-electronic protective devices (AOPDs) for the sensing function.
IEC 61496-3Specifies additional requirements for the design, construction and testing of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety related system, employing active opto-electronic protective devices responsive to diffuse(...)
IEC 61500IEC 61500:2009 establishes requirements for data communication which is used in systems performing category A functions in nuclear power plants. It covers also interface requirements for data communication of equipment performing category A functions with other systems including those(...)
IEC 61501Describes the principles, the terminology, the characteristics, the requirements and the testing methods related to instrumentation and measurement of the neutron fluence rate using mean square voltage techniques for nuclear reactor control.
IEC 61502Applies to systems used for monitoring the vibratory behaviour of the internal structures of pressurized water reactors (core barrel, thermal shield, upper and lower core support, etc.) and fuel assemblies on the basis of neutron fluctuations observed outside the vessel and vessel vibrations.(...)
IEC 61508-1Covers those aspects to be considered when electrical/electronic/programmable electronic (E/E/PE) systems are used to carry out safety functions
