EN 620:2002+A1:2010This European standard deals with the technical requirements to minimise the risks due to the hazards listed in clause 4, which can arise during operation and maintenance of fixed belt conveyors and systems as defined in 3.1 to 3.2.4 and designed for continuously conveying loose bulk materials(...)
EN 1155:1997This European Standard specifies requirements for separate hold-open devices and also for hold-open mechanisms incorporated in a door closer. Electrically powered hold-open devices for swing doors manufactured according to this European Standard can hold a swing door at a fixed position or can(...)
EN 12015:2014This European Standard specifies the emission limits in relation to electromagnetic disturbances and test conditions for lifts, escalators and moving walks, which are intended to be permanently installed in buildings.
EN 12016:2013Specifies the immunity performance criteria and test levels for apparatus used in lifts, escalators and moving walks which are intended to be permanently installed in buildings including the basic safety requirements in regard to their electromagnetic environment. These levels represent(...)
EN 12895:2000Applies to industrial trucks regardless of the power source (called only trucks) as defined in ISO 5053, variable reach trucks and their electrical/electronic systems when used in Residential, Commercial, Light Industry and Industrial Environment. This standard defines : - the requirements and(...)
EN 13309:2010Provides test methods and acceptance criteria for the evaluation of the electromagnetic compatibility of construction machinery with respect to free trade of goods in the European Union. It deals with functional EMC requirements under typical EMC environmental conditions.
EN 14010:2003+A1:2009Deals with the technical requirements to minimize the risks due to the hazards listed in clause 4, which can arise during installation , operation and maintenance of permanently installed equipment and systems for the power driven parking of motor vehicles, as defined in 3.1 to 3.4 below.(...)
EN 50270:2006Specifies requirements for the electromagnetic compatibility (EMC) for electrical apparatus for the detection and measurement of combustible gases, toxic 1) gases or oxygen. This standard applies to apparatus intended for use in residential, commercial and light-industrial environments as well(...)
EN 50295:1999Specifies requirements for a bit-orientated interface system between a single controlling device and control circuit devices as defined in BS EN 60947-1, connected by an unshielded, untwisted two-wire cable carrying data and power.
EN 50428:2005+A2:2009This collateral standard applies to HBES switches with a working voltage not exceeding 250 V a.c. and a rated current up to and including 16 A. for household and similar fixed electrical installations either indoors or outdoors and to associated electronic extension units. It applies – to HBES(...)
EN 50490:2008This European Standard is intended to give general minimum frame requirements for units that are independent of the technology used for switching and/or monitoring of individual or group of lamps in an AGL series circuit. This European Standard • applies to the units that are directly(...)
EN 50498:2010Specifies limits and methods of measurement for disturbance emissions and immunity characteristics of aftermarket equipment (ESAs) which are referenced by Automotive EMC Directive 2004/104/EC, Annex I, 3.2.9, and which are not related to immunity-related functions of vehicles as defined in(...)
EN 50550:2011Applies to power frequency overvoltage protection devices (hereafter referred to as “POP”) for household and similar uses, with a rated frequency of 50 Hz, a rated voltage 230 V a.c. (between phase and neutral), intended to be used in combination with a main protective device being either a CB(...)
EN 55013:2013Applies to the generation of electromagnetic energy from sound and television receivers for the reception of broadcast and similar transmissions and from associated equipment. CISPR 13:2009 describes the methods of measurement applicable to sound and television receivers or associated(...)
EN 55015:2013Applies to the emission (radiated and conducted) of radio frequency disturbances from: - all lighting equipment with a primary function of generating and/or distributing light intended for illumination purposes, and intended either for connection to the low voltage electricity supply or for(...)
EN 55020:2007/A11:2011Applies to television broadcast receivers, sound broadcast receivers and associated equipment intended for use in the residential, commercial and light industrial environment. Describes the methods of measurement and specified limits applicable to sound and television receivers and to(...)
EN 55022:2010/AC:2011Applies to information technology equipment (ITE). Procedures are given for the measurement of the levels of spurious signals generated by the ITE and limits are specified for the frequency range 9 kHz to 400 GHz for both class A and class B equipment.
EN 55024:2010Defines the immunity test requirements for information technology equipment (ITE, as defined in CISPR 22) in relation to continuous and transient, conducted and radiated disturbances, including electrostatic discharges (ESD). Procedures are defined for the measurement of ITE and limits are(...)
EN 60945:2002Specifies minimum performance requirements, methods of testing and required test results for general requirements which can be applied to those characteristics common to the following equipment: shipborne radio equipment, shipborne navigational equipment, and, for EMC only, all other(...)
EN 61543:1996Ensures electromagnetic compatibility (EMC) of devices providing residual current protection, for rated voltages not exceeding 440 V a.c., intended principally for protection of persons against shock hazards.
