EN 61439-5:2011Gives specific requirements for public electricity network distribution assemblies (PENDAs), which are stationary assemblies verified by verification tests, as defined in this standard. These ASSEMBLIES are used for the distribution of electrical energy in three-phase systems (see Figure 101(...)
EN 61557-12:2008Specifies requirements for combined performance measuring and monitoring devices that measure and monitor the electrical parameters within electrical distribution systems. These requirements also define the performance, in single and three-phase a.c. or d.c. systems having rated voltages up to(...)
EN 61800-3:2004Specifies electromagnetic compatibility (EMC) requirements for power drive systems (PDSs). A PDS is defined in 3.1. These are adjustable speed a.c. or d.c. motor drives. Requirements are stated for PDSs with converter input and/or output voltages (line-to-line voltage), up to 35 kV a.c. r.m.s.
EN 61812-1:2011Applies to time relays for industrial applications (e.g. control, automation, signal and industrial equipment). It also applies to time relays for automatic electrical controls for use in, on, or in association with equipment for residential and similar use.
EN 62026-1:2007Applies to interfaces between low-voltage switchgear, controlgear, and controllers (e.g. programmable controllers, personal computers, etc.). This standard does not apply to higher level industrial communication networks that have become known as fieldbuses and are considered by IEC(...)
EN 62026-3:2009Specifies an interface system between single or multiple controllers, and control circuit devices or switching elements. The interface system uses two twisted shielded conductor pairs within one cable - one of these pairs provides a differential communication medium and the other pair provides(...)
EN 62040-2:2006Is intended as a product standard allowing the EMC conformity assessment of products of categories C1, C2 and C3 as defined in this part of EN 62040, before placing them on the market.The requirements have been selected so as to ensure an adequate level of electromagnetic compatibility (EMC)(...)
EN 62052-11:2003Covers type tests for electricity metering equipment for indoor and outdoor application and to newly manufactured equipment designed to measure the electric energy on 50 Hz or 60 Hz networks, with a voltage up to 600 V. It applies to electromechanical or static meters for indoor and outdoor(...)
EN 62052-21:2004Specifies general requirements for the type test of newly manufactured indoor tariff and load control equipment, like electronic ripple control receivers and time switches that are used to control electrical loads, multi-tariff registers and maximum demand indicator devices.
EN 62053-11:2003Applies only to newly manufactured electromechanical watt-hour meters of accuracy classes 0,5, 1 and 2, for the measurement of alternating current electrical active energy in 50 Hz or 60 Hz networks and it applies to their type tests only. It applies only to electromechanical watt-hour meters(...)
EN 62053-21:2003Applies only to newly manufactured static watt-hour meters of accuracy classes 1 and 2, for the measurement of alternating current electrical active energy in 50 Hz or 60 Hz networks and it applies to their type tests only. It applies only to static watt-hour meters for indoor and outdoor(...)
EN 62053-22:2003Applies only to newly manufactured static watt-hour meters of accuracy classes 0,2 S and 0,5 S, for the measurement of alternating current electrical active energy in 50 Hz or 60 Hz networks and it applies to their type tests only.
EN 62053-23:2003Applies only to newly manufactured static var-hour meters of accuracy classes 2 and 3, for the measurement of alternating current electrical reactive energy in 50 Hz or 60 Hz networks and it applies to their type tests only. For practical reasons, this standard is based on a conventional(...)
EN 62054-11:2004Specifies particular requirements for the type test of newly manufactured indoor electronic ripple control receivers for the reception and interpretation of pulses of a single audio frequency superimposed on the voltage of the electricity distribution network and for the execution of the(...)
EN 62054-21:2004Specifies particular requirements for the type test of newly manufactured indoor time switches with operation reserve that are used to control electrical loads, multi-tariff registers and maximum demand devices of electricity metering equipment
EN 62135-2:2008Specifies test methods to be used in conjunction with CISPR 11 to determine radiofrequency emission; relevant standards and test methods for harmonic current emission, voltage fluctuation and flicker. Also defines immunity requirements and test methods for continuous and transient, conducted(...)
EN 62310-2:2007Applies to free standing operation a.c. static transfer systems (STS) intended to ensure the continuity of load supply through controlled transfer, with or without interruption of power, from two or more independent a.c. sources.includes requirements for the switching elements, their control(...)
EN 617:2001+A1:2010This standard deals with safety related technical verification during commissioning. The following parts are dealt with in this standard (see Figure 1) A Bulk material to be stored B Storage space limited by the silo structure C Charging D Discharging E Associated and additional equipment(...)
EN 618:2002+A1:2010This standard is applicable to continuously-operating equipment and systems designed for the mechanical handling of bulk materials only, including mobile machines. This standard relates to the following groups of equipment. - Fixed equipment, such as belt, apron, screw "en masse" conveyors and(...)
EN 619:2002+A1:2010This standard applies to mechanical conveyor devices designed exclusively for moving unit loads continuously on a predefined route from the loading to the unloading point, possibly with varying speed or cyclically. It also applies to continuous conveyors which are built into machines or(...)
