IEC 62108Specifies the minimum requirements for the design qualification and type approval of concentrator photovoltaic modules and assemblies suitable for long-term operation in general open-air climates.
IEC 62109-1IEC 62109-1:2010(E) applies to the power conversion equipment (PCE) for use in photovoltaic systems where a uniform technical level with respect to safety is necessary. Defines the minimum requirements for the design and manufacture of PCE for protection against electric shock, energy, fire,(...)
IEC 62109-2IEC 62109-2:2011 covers the particular safety requirements relevant to d.c. to a.c. inverter products as well as products that have or perform inverter functions in addition to other functions, where the inverter is intended for use in photovoltaic power systems. Inverters covered by this(...)
IEC 62115Deals with the safety of toys that have at least one function dependent on electricity. Examples of toys within the scope of this standard are: constructional sets; experimental sets; functional toys (having a function similar to an appliance or installation used by adults) and video toys(...)
IEC 62116IEC 62116:2014 provides a test procedure to evaluate the performance of islanding prevention measures used with utility-interconnected PV systems. This standard describes a guideline for testing the performance of automatic islanding prevention measures installed in or with single or(...)
IEC 62117Gives requirements for instrumentation to monitor core cooling for safe operation of PWRs during cold shutdown operations when the coolant temperature is below 100 °C. Summarizes good international practices to be used when designing new or upgrading existing PWR core cooling monitors.
IEC 62124Verifies system design and performance of stand-alone photovoltaic systems. The performance test consists of a check of the functionality, the autonomy and ability to recover after periods of low state-of-charge of the battery, and hence gives reasonable assurance that the system will not fail(...)
IEC 62138Provides requirements for the software of computer-based I&C systems performing functions of safety category B or C as defined by IEC 61226.
IEC 62192Covers insulating ropes that are utilized during live working procedures in contact with parts of installations operating at voltages up to and including 800 kV r.m.s.
IEC 62193Covers telescopic sticks and telescopic measuring sticks to be used for live working on a.c. or d.c. electrical installations at 1 000 V and above for a.c. and 1 500 V and above for d.c.
IEC 62196-1Applicable to plugs, socket-outlets, vehicle connectors, vehicle inlets and cable assemblies for electric vehicles, herein referred to as “accessories”, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding 690 V a.c.(...)
IEC 62196-3IEC 62196-3:2014 is applicable to vehicle couplers with pins and contact-tubes of standardized configuration, herein also referred to as “accessories”, intended for use in electric vehicle conductive charging systems which incorporate control means, with rated operating voltage up to 1 500 V(...)
IEC 62232Addresses the evaluation of RF field strength or specific absorption rate levels in the vicinity of non-broadcast RF radiocommunication sources (i.e. RBS) intentionally radiating in the frequency range 300 MHz to 6 GHz according to the scope (see Clause 1).
IEC 62237Is applicable to mobile insulating hoses with fittings used with hydraulic tools and equipment for live working at nominal voltages exceeding 1 kV r.m.s. at power frequency. Insulating hoses with fittings are used to provide a connection between the hydraulic tool and the pump which are at(...)
IEC 62241Provides the functional requirements for the alarm systems in the main control room of nuclear power plants. Establishes the human factors requirements and the design guidelines for alarm presentation for the main control room of nuclear power plants.
IEC 62244Defines the performance of installed monitors used for the detection of gamma and neutron radiation emitters contained in objects/ containers or vehicles, general characteristics, mechanical characteristics, environmental requirements, test procedures and documentation.
IEC 62253IEC 62253:2011 defines the requirements for design, qualification and performance measurements of photovoltaic (PV) pumping systems in stand-alone operation. The outlined measurements are applicable for either indoor tests with PV generator simulator or outdoor tests using a real PV generator.
IEC 62256Provides assistance in identifying, evaluating and executing rehabilitation and performance improvement projects for hydraulic turbines, storage pumps and pump-turbines of all sizes and of the following types: Francis; Kaplan; Propeller; Pelton (turbines only); Bulb.
IEC 62270IEC 62270:2013 addresses the application, design concepts, and implementation of computer-based control systems for hydroelectric plant automation. It addresses functional capabilities, performance requirements, interface requirements, hardware considerations, and operator training. It(...)
IEC 62282-2IEC 62282-2:2012 provides the minimum requirements for safety and performance of fuel cell modules; it applies to fuel cell modules with or without an enclosure which can be operated at significant pressurization levels or close to ambient pressure. Deals with conditions that can yield hazards(...)
