i
Search:
(clear)
Applies to systems used for monitoring the vibratory behaviour of the internal structures of pressurized water reactors (core barrel, thermal shield, upper and lower core support, etc.) and fuel assemblies on the basis of neutron fluctuations observed outside the vessel and vessel vibrations.(...)
IEC 61513:2011 provides requirements and recommendations for the overall I&C architecture which may contain either or both technologies.
IEC 61646:2008 lays down requirements for the design qualification and type approval of terrestrial, thin-film photovoltaic modules suitable for long-term operation in general open-air climates as defined in IEC 60721-2-1.
Describes guidelines for measuring the efficiency of power conditioners used in stand-alone and utility-interactive photovoltaic systems, where the output of the power conditioner is a stable a.c. voltage of constant frequency or a stable d.c. voltage.
IEC 61701:2011 describes test sequences useful to determine the resistance of different PV modules to corrosion from salt mist containing Cl- (NaCl, MgCl2, etc.). All tests included in the sequences, except the bypass diode functionality test, are fully described in IEC 61215, IEC 61646, IEC(...)
Recommends procedures for the monitoring of energy-related photovoltaic (PV) system characteristics, and for the exchange and analysis of monitored data. The purpose is the assessment of the overall performance of PV systems.
Provides a normative equation for analytically deriving a set of data points or a curve of irradiance versus time of day for a synthetic solar day.
Applies to utility-interconnected photovoltaic (PV) power systems operating in parallel with the utility and utilizing static (solid-state) non-islanding inverters for the conversion of DC to AC. Lays down requirements for interconnection of PV systems to the utility distribution system.
Describes the fundamental construction requirements for photovoltaic modules in order to provide safe electrical and mechanical operation during their expected lifetime. Addresses the prevention of electrical shock, fire hazards, and personal injury due to mechanical and environmental stresses.
Describes the testing requirements for photovoltaic modules in order to provide safe electrical and mechanical operation during their expected lifetime. Addresses the prevention of electrical shock, fire hazards, and personal injury due to mechanical and environmental stresses.
Specifies verification and validation procedures for the design of the control-room system of nuclear power plants and gives verification and validation criteria for the assignment of functions and for the integrated control-room system.
IEC 61772:2009 supplements IEC 60964 and presents design requirements for the application of VDUs in main control rooms of nuclear power plants. Assists the designer in specifying VDU applications including displays on individual workstations and larger displays for group-working or distant viewing.
Describes procedures for on-site measurement of crystalline silicon photovoltaic (PV) array characteristics and for extrapolating these data to Standard Test Conditions (STC) or other selected temperatures and irradiance values.
Specifies functional analysis and assignment procedures for the design of the control-room system for nuclear power plants and gives rules for developing criteria for the assignment of functions. Supplements IEC 60964. Is applicable to the design of new control-rooms or to backfits to existing(...)
IEC 61853-1:2011 describes requirements for evaluating PV module performance in terms of power (watts) rating over a range of irradiances and temperatures. The object is to define a testing and rating system, which provides the PV module power (watts) at maximum power operation for a set of(...)
Defines the requirements for assuring that automatic setpoints for nuclear safety system instrumentation are established and maintained within specified limits in nuclear power plants and nuclear reactor facilities.
Provides a uniform method for describing and characterizing the background in a spectrum from an HPGe detector. Provides both manufacturers and end users with a way to specify the low-background performance of the detector and allows the comparison of detectors used for these kinds of measurements.
IEC 62003:2009 establishes requirements for electromagnetic compatibility testing of instrumentation and control equipment supplied for use in systems important to safety at nuclear power plants
Defines the test, the measuring methods and the contractual guarantee conditions for field acceptance tests of the generating machinery in small hydroelectric power installations. It applies to installations containing impulse or reaction turbines with unit power up to about 15 MW and(...)
Establishes standard test procedures for photodiodes used in scintillation detectors and defines the parameters which shall be provided by the supplier for each type of photodiode.
Establishes standard methods for calibration and use of alpha/beta gas proportional counters, including measurement of their characteristics. Applies to alpha/beta gas proportional counting systems used for the determination of the alpha-ray or beta-ray emission rates of radionuclides in(...)
Establishes requirements for the design qualification of balance-of-system (BOS) components used in terrestrial photovoltaic systems. Is suitable for operation in indoor, conditioned or unconditioned; or outdoor in general open-air climates, protected or unprotected. Is written for dedicated(...)
IEC 62097:2009 is applicable to the assessment of the efficiency and performance of prototype hydraulic machine from model test results, with consideration of scale effect including the effect of surface roughness.
Specifies the minimum requirements for the design qualification and type approval of concentrator photovoltaic modules and assemblies suitable for long-term operation in general open-air climates.
IEC 62109-1:2010(E) applies to the power conversion equipment (PCE) for use in photovoltaic systems where a uniform technical level with respect to safety is necessary. Defines the minimum requirements for the design and manufacture of PCE for protection against electric shock, energy, fire,(...)
IEC 62109-2:2011 covers the particular safety requirements relevant to d.c. to a.c. inverter products as well as products that have or perform inverter functions in addition to other functions, where the inverter is intended for use in photovoltaic power systems. Inverters covered by this(...)
IEC 62116:2014 provides a test procedure to evaluate the performance of islanding prevention measures used with utility-interconnected PV systems. This standard describes a guideline for testing the performance of automatic islanding prevention measures installed in or with single or(...)
Gives requirements for instrumentation to monitor core cooling for safe operation of PWRs during cold shutdown operations when the coolant temperature is below 100 °C. Summarizes good international practices to be used when designing new or upgrading existing PWR core cooling monitors.
Verifies system design and performance of stand-alone photovoltaic systems. The performance test consists of a check of the functionality, the autonomy and ability to recover after periods of low state-of-charge of the battery, and hence gives reasonable assurance that the system will not fail(...)
Provides requirements for the software of computer-based I&C systems performing functions of safety category B or C as defined by IEC 61226.