EMC Standards

AJAX progress indicator
  • e

  • EN 62053-23:2003
    Applies only to newly manufactured static var-hour meters of accuracy classes 2 and 3, for the measurement of alternating current electrical reactive energy in 50 Hz or 60 Hz networks and it applies to their type tests only. For practical reasons, this standard is based on a conventional(...)
  • EN 62054-11:2004
    Specifies particular requirements for the type test of newly manufactured indoor electronic ripple control receivers for the reception and interpretation of pulses of a single audio frequency superimposed on the voltage of the electricity distribution network and for the execution of the(...)
  • EN 62054-21:2004
    Specifies particular requirements for the type test of newly manufactured indoor time switches with operation reserve that are used to control electrical loads, multi-tariff registers and maximum demand devices of electricity metering equipment
  • EN 62135-2:2008
    Specifies test methods to be used in conjunction with CISPR 11 to determine radiofrequency emission; relevant standards and test methods for harmonic current emission, voltage fluctuation and flicker. Also defines immunity requirements and test methods for continuous and transient, conducted(...)
  • EN 62310-2:2007
    Applies to free standing operation a.c. static transfer systems (STS) intended to ensure the continuity of load supply through controlled transfer, with or without interruption of power, from two or more independent a.c. sources.includes requirements for the switching elements, their control(...)
  • EN 62423:2012
    This standard specifies requirements and tests for type B RCDs. Requirements and tests given in this standard are in addition to the requirements of type A residual current devices. Type B RCCBs and Type B RCBOs are able to provide protection in case of alternating residual sinusoidal currents(...)
  • EN ISO 14982:2009
    Specifies test methods and acceptance criteria for evaluating the electromagnetic compatibility of tractors and all kinds of mobile (including hand-held) agricultural machinery, forestry machinery, landscaping and gardening machinery.
  • f

  • FCC Part 15 - Radio Frequency Devices
    US limits and methods of measurement of radio disturbance, measuring radio waves accidentally emitted from devices not specifically designed to emit radio waves ("unintentional"), both directly ("radiated") and indirectly ("conducted")
  • i

  • IEC 60034-2-1
    This standard is intended to establish methods of determining efficiencies from tests, and also to specify methods of obtaining specific losses. This standard applies to d.c. machines and to a.c. synchronous and induction machines of all sizes within the scope of IEC 60034-1. 
  • IEC 60297-3-108
    IEC 60297-3-108:2014 provides dimensions and features for R-type subracks and plug-in units, i.e. ruggedized variants of the mechanical structures of the 482,6 mm (19 in) series, with enhanced vibration and shock resistance and/or improved EMC performance, for use in more harsh environment.
  • IEC 60601-1-2
    IEC 60601-1-2:2014 applies to the basic safety and essential performance of Medical Equipment (ME) equipment and ME systems in the presence of electromagnetic disturbances and to electromagnetic disturbances emitted by me equipment and me systems. 
  • IEC 61000-4-1
    The object of this part of IEC 61000 is to give applicability assistance to the technical committees of IEC or other bodies, users and manufacturers of electrical and electronic equipment on EMC standards within the IEC 61000-4 series on testing and measurement techniques and to provide(...)
  • IEC 61000-4-10
    IEC 61000-4-10 relates to the immunity requirements of equipment, only under operational conditions, to damped oscillatory magnetic disturbances related to medium voltage and high voltage sub-stations
  • IEC 61000-4-11
    This part of IEC 61000 defines the immunity test methods and range of preferred test levels for electrical and electronic equipment connected to low-voltage power supply networks for voltage dips, short interruptions, and voltage variations. This standard applies to electrical and electronic(...)
  • IEC 61000-4-12
    This part of IEC 61000 relates to the immunity requirements and test methods for electrical and electronic equipment, under operational conditions, to non-repetitive damped oscillatory transients (ring waves) occurring in low-voltage power, control and signal lines supplied by public and(...)
  • IEC 61000-4-13
    IEC 61000-4-13:2002+A1:2009 defines the immunity test methods and range of recommended basic test levels for electrical and electronic equipment with rated current up to 16 A per phase at disturbance frequencies up to and including 2 kHz (for 50 Hz mains) and 2,4 kHz (for 60 Hz mains) for(...)
  • IEC 61000-4-14
    IEC 61000-4-14:1999+A1:2001+A2:2009 applies to electrical and/or electronic equipment that have a rated input current up to 16 A per phase. Aims to establish a reference for evaluating the immunity of electric and/or electronic equipment when subjected to positive and negative low amplitude(...)
  • IEC 61000-4-15
    IEC 61000-4-15:2010 gives a functional and design specification for flicker measuring apparatus intended to indicate the correct flicker perception level for all practical voltage fluctuation waveforms. Information is presented to enable such an instrument to be constructed. A method is given(...)
  • IEC 61000-4-16
    IEC 61000-4-16:1998+A1:2001+A2:2009 Establishes a common and reproducible basis for testing electrical and electronic equipment with the application of common mode disturbances to power supply, control, signal and communication ports. This standard defines test voltage and current waveform,(...)
  • IEC 61000-4-17
    IEC 61000-4-17 defines test methods for immunity to ripple at the d.c. input power port of electrical or electronic equipment. Applies to low-voltage d.c. power ports of equipment supplied by external rectifier systems, or batteries which are being charged. This standard defines test voltage(...)
  • IEC 61000-4-18
    EC 61000-4-18:2006+A1:2010 relates to the immunity requirements and test methods for electrical and electronic equipment, under operational conditions, with regard to: repetitive damped oscillatory waves occurring mainly in power, control and signal cables installed in high voltage and medium(...)
  • IEC 61000-4-19
    IEC 61000-4-19:2014 relates to the immunity requirements and test methods for electrical and electronic equipment to conducted, differential mode disturbances and signalling in the range 2 kHz up to 150 kHz at a.c. power ports.
  • IEC 61000-4-2 
    IEC 61000-4-2:2008 relates to the immunity requirements and test methods for electrical and electronic equipment subjected to static electricity discharges, from operators directly, and from personnel to adjacent objects. It additionally defines ranges of test levels which relate to different(...)
  • IEC 61000-4-20
    IEC 61000-4-20:2010 relates to emission and immunity test methods for electrical and electronic equipment using various types of transverse electromagnetic (TEM) waveguides. These types include open structures (for example, striplines and electromagnetic pulse simulators) and closed structures(...)
  • IEC 61000-4-21
    IEC 61000-4-21:2011 considers tests of immunity and intentional or unintentional emissions for electric and/or electronic equipment and tests of screening effectiveness in reverberation chambers. It establishes the required test procedures for performing such tests. Only radiated phenomena are(...)
  • IEC 61000-4-22
    IEC 61000-4-22:2010 considers immunity tests and emission measurements for electric and/or electronic equipment. Only radiated phenomena are considered. It establishes the required test procedures for using fully anechoic rooms for performing radiated immunity testing and radiated emission(...)
  • IEC 61000-4-23
    IEC 61000-4-23 provides the basic reasons behind HEMP testing and gives a brief description of the most important concepts for shielding element testing. For each test, the following basic information is provided: - theoretical foundation of the test (the test concept); - test set-up; -(...)
  • IEC 61000-4-24
    IEC 61000-4-24 deals with methods for testing protective devices for HEMP conducted disturbance. It primarily covers testing of voltage breakdown and voltage-limiting characteristics but also methods to measure the residual voltage under HEMP conditions for the case of very fast changes of(...)
  • IEC 61000-4-25
    IEC 61000-4-25:2001+A1:2012 describe immunity test levels and related test methods for electrical and electronic equipment and systems exposed to high-altitude electromagnetic pulse (HEMP) environments. Specifications for test equipment and instrumentation test set-up, test procedures,(...)
  • IEC 61000-4-27
    IEC 61000-4-27:2000+A1:2009 considers immunity tests for electric and/or electronic equipment (apparatus and system) in its electromagnetic environment. Only conducted phenomena are considered, including immunity tests for equipment connected to public and industrial networks. Establishes a(...)