CISPR 18-3:2010(E), which is a technical report, applies to radio noise from overhead power lines and high-voltage equipment which may cause interference to radio reception, excluding the fields from power line carrier signals. The frequency range covered is 0,15 MHz to 300 MHz.
This European Standard specifies requirements for separate hold-open devices and also for hold-open mechanisms incorporated in a door closer. Electrically powered hold-open devices for swing doors manufactured according to this European Standard can hold a swing door at a fixed position or can(...)
Specifies the emission limits in relation to electromagnetic disturbances and test conditions for lifts, escalators and moving walks, which are intended to be permanently installed in buildings. These limits however, may not provide full protection against disturbances caused to radio and TV(...)
Specifies the immunity performance criteria and test levels for apparatus used in lifts, escalators and moving walks which are intended to be permanently installed in buildings including the basic safety requirements in regard to their electromagnetic environment. These levels represent(...)
Applies to industrial trucks regardless of the power source (called only trucks) as defined in ISO 5053, variable reach trucks and their electrical/electronic systems when used in Residential, Commercial, Light Industry and Industrial Environment. This standard defines : - the requirements and(...)
Specifies the safety and performance requirements for doors, gates and barriers, intended for installation in areas in the reach of persons, and for which the main intended uses are giving safe access for goods and vehicles accompanied or driven by persons in industrial, commercial or(...)
Provides test methods and acceptance criteria for the evaluation of the electromagnetic compatibility of construction machinery with respect to free trade of goods in the European Union. It deals with functional EMC requirements under typical EMC environmental conditions.
Deals with the technical requirements to minimize the risks due to the hazards listed in clause 4, which can arise during installation , operation and maintenance of permanently installed equipment and systems for the power driven parking of motor vehicles, as defined in 3.1 to 3.4 below.(...)
This standard addresses detailed system requirements (Clause 4), general test conditions, verification requirements at system level, and test methods at subsystem and equipment level (Clause 5) as well as informative limits (Annex A).
This European Standard specifies the characteristics of single-pole circuit breakers, temperature compensated with a rated current from 20 A to 25 A, used in aircraft on-board circuits at a temperature between – 55 °C and 125 °C and at an altitude of 15 000 m max.
Covers the EMC requirements for non-radio equipment intended to be used within a public telecommunications network, which provides telecommunications between Network Termination Points (NTPs) (i.e. excluding terminal equipment beyond the NTPs)
Contains the common requirements for radio communications equipment and associated ancillary equipment, in respect of ElectroMagnetic Compatibility (EMC).
Contains the Specific ElectroMagnetic Compatibility (EMC) requirements for the common external power supply (EPS) for use with data-enabled mobile telephones as described in EN 62684 and M/455
Specifies the required characteristics of a light weight coaxial cable, 50 Ω, type KW for use in aircraft electrical systems at operating temperature between 55 °C and 180 °C and specially for high frequency up to 6 GHz.
This standard applies to electrical equipment using signals in the frequency range 3 kHz to 148,5 kHz to transmit information on low voltage electrical systems, either on the public electricity distribution network or within installations in consumers’ premises. It specifies the frequency(...)
Defines the general technical requirements of a Home and Building Electronic System (HBES) based on SELV or PELV. It concerns cabling and topology, electrical and functional safety, environmental conditions and behavior in case of failures as well as specific HBES installation rules. The HBES(...)
This Part 1 of the European standards series EN 50121 outlines the structure and the content of the whole set. This part alone is not sufficient to give presumption of conformity to the essential requirements of the EMC-Directive and must be used in conjunction with other parts of this(...)
Specifies the emission and immunity requirements for all types of rolling stock. It covers traction stock and trainsets including urban vehicles for use in city streets. The frequency range considered is from d.c. to 400 GHz.
Applies to signalling and telecommunication apparatus which is installed in the railway environment. Signalling and telecommunication apparatus mounted in vehicles is covered by EN 50121-3-2. This standard specifies limits for emission and immunity and provides performance criteria for(...)
Applies to emission and immunity aspects of EMC for electrical and electronic apparatus and systems intended for use in railway fixed installations associated with power supply. This includes the power feed to the apparatus, the apparatus itself with its protective control circuits, trackside(...)
This EMC product-family standard, for immunity requirements, applies to the components of the following alarm systems, intended for use in and around buildings in residen¬tial, commercial, light industrial and industrial environments: – access control systems, for security applications; –(...)
Specifies requirements for the electromagnetic compatibility (EMC) for electrical apparatus for the detection and measurement of combustible gases, toxic 1) gases or oxygen. This standard applies to apparatus intended for use in residential, commercial and light-industrial environments as well(...)
Specifies requirements for a bit-orientated interface system between a single controlling device and control circuit devices as defined in BS EN 60947-1, connected by an unshielded, untwisted two-wire cable carrying data and power.
Applies to electrical equipment using signals in the frequency range 1.6 MHz to 30 MHz to transmit information on low voltage electrical systems, either on the public supply system or within installations in consumers' premises.It does not specify the signal modulation methods nor the coding(...)
This collateral standard applies to HBES switches with a working voltage not exceeding 250 V a.c. and a rated current up to and including 16 A. for household and similar fixed electrical installations either indoors or outdoors and to associated electronic extension units. It applies – to HBES(...)
This European Standard is intended to give general minimum frame requirements for units that are independent of the technology used for switching and/or monitoring of individual or group of lamps in an AGL series circuit. This European Standard • applies to the units that are directly(...)