i
Search:
(clear)
Applies to hand-held instruments used for the detection and localization of radioactive photon emitting materials.
Applies to hand-held instruments used for the detection and localization of neutron emitting radioactive material.
Specifies generic terms and definitions that are related to environmental standardization within the IEC. It serves as a glossary of terminology to be considered for environmental aspects of relevant work in IEC.
Applies to a single stand-alone broadcast transmitter operating in the frequency range 30 MHz to 40 GHz when put on the market. The objective of the standard is to specify, for such equipment operating in typical conditions, the method for assessment of compliance distances according to the(...)
IEC 62598:2011 applies to the manufacture and installation of electrical measuring systems and instruments utilizing radioactive sources (radiometric gauges, hereinafter called gauges). It also applies to source housings intended for use in the aforementioned measuring systems.
Specifies environmental test methods to be used for testing the system components of the following alarm systems, intended for use in and around buildings
Immunity requirements applies to the components of the following alarm systems, intended for use in and around buildings in residential, commercial, light industrial and industrial environments
Standard establishes performance requirements, provides examples of acceptable test methods and specifies general characteristics, general test conditions, radiological, environmental, mechanical and electromagnetic characteristics that are used to determine if an instrument meets the(...)
This IEC standard describes dielectric and resistive properties of solid insulating materials.
Specifies the requirements for intrusion and hold-up alarm systems (I&HAS) installed in buildings using specific or non-specific wired interconnections or wire-free interconnections
Is for passive infrared detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
Is for microwave detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
Is for combined passive infrared and microwave detectors installed in buildings and provides for security Grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
Is for combined passive infrared and ultrasonic detectors installed in buildings and provides for security grades 1 to 4 (see IEC 62642-1), specific or non-specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1).
Applies to intrusion alarm equipment using radio frequency links and located on protected premises. This standard defines the terms used in the field of intrusion alarm equipment using radio frequency links as well as the requirements relevant to the equipment.
Specifies the requirements, performance criteria and testing procedures for power supplies (PS) to be used as part of Intrusion and Hold up Alarm Systems (I&HAS).
Specifies the requirements for security fog systems as a part of an I&HAS. It covers application and performance and also gives the necessary tests and trials to ensure efficiency and reliability of such obscuration devices. It also gives guidance on the criteria for design, installation,(...)
IEC 62646:2012 establishes requirements for the whole life cycle of operating procedures that the designer wishes to computerise. It also provides guidance for making decisions about which types of procedures are to be computerised and to what extent. Once computerised, procedures are(...)
IEC 62651:2013 describes the requirements for thermocouples suitable for nuclear power plant (NPP) applications. The requirements given in this standard for thermocouples include design, materials, manufacturing, testing, calibration, procurement, and inspection.
IEC 62670-1:2013 defines standard conditions for assessing the power produced by CPV systems and their photovoltaic subcomponents. The object is to define a consistent set of conditions so that power ratings noted on data sheets and nameplates will have a standard basis.
IEC 62671:2013 addresses certain devices that contain embedded software or electronically-configured digital circuits that have not been produced to other IEC Standards which apply to systems and equipment important to safety in nuclear power plants, but which are candidates for use in nuclear(...)
Specifies the minimum requirements and gives recommendations for Video Surveillance Systems (VSS) (so far called CCTV), installed for security applications.
Introduces general requirements on video transmission. This standard covers the general requirements for video transmissions on performance, security and conformance to basic IP connectivity, based on available, well-known, international standards.
Introduces an IP network interface for devices in surveillance applications. This International Standard specifies a network protocol for the full interoperability of video devices.
Specifies a compliant IP video protocol based on HTTP and REST services. Video transmission devices are often equipped with web servers that respond to HTTP requests.
Defines procedures for communication between network video clients and video transmitter devices based on Web Services. This new set of specifications makes it possible to build network video systems with devices and receivers from different manufacturers using common and well defined interfaces.
Specifies physical, electrical and software interface (non-IP) specifications of analog and digital video interface in video surveillance systems (so far called CCTV) applications.
Establishes the environmental, mechanical and electromagnetic performance requirements and methods of test for radiation protection instrumentation.
IEC 62716:2013 describes test sequences useful to determine the resistance of PV modules to ammonia (NH3).