Standards Library

AJAX progress indicator
  • i

  • IEC 61400-25-3
    Specifies an abstract communication service interface describing the information exchange between a client and a server for: data access and retrieval, device control, event reporting and logging, publisher/subscriber, self-description of devices (device data dictionary), data typing and(...)
  • IEC 61400-25-4
    IEC 61400-25-4:2008(E) specifies the specific mappings to protocol stacks encoding the messages required for the information exchange between a client and a remote server for data access and retrieval, device control, event reporting and logging, publisher/subscriber, self-description of(...)
  • IEC 61400-25-5
    Specifies standard techniques for testing of conformance of implementations, as well as specific measurement techniques to be applied when declaring performance parameters.
  • IEC 61400-25-6
    IEC 61400-25-6:2010(E) specifies the information models related to condition monitoring for wind power plants and the information exchange of data values related to these models.
  • IEC 61400-3
    IEC 61400-3:2009 specifies additional requirements for assessment of the external conditions at an offshore wind turbine site and specifies essential design requirements to ensure the engineering integrity of offshore wind turbines.
  • IEC 61400-4
    IEC 61400-4:2012(E) is applicable to enclosed speed increasing gearboxes for horizontal axis wind turbine drivetrains with a power rating in excess of 500 kW. This standard applies to wind turbines installed onshore or offshore. It provides guidance on the analysis of the wind turbine loads in(...)
  • IEC 61427-1
    IEC 61427-1:2013 is part of a series which gives general information relating to the requirements for the secondary batteries used in photovoltaic energy systems (PVES) and to the typical methods of test used for the verification of battery performances.
  • IEC 61435
    IEC 61435:2013(E) is applicable to high-purity germanium crystals used for radiation detectors for gamma-rays and X-rays. Such germanium is monocrystalline and has a net concentration of fewer than 1011 electrically active impurity centers per cm3. This International Standard specifies(...)
  • IEC 61453
    Specifies methods of calibration and routine tests of scintillation detector systems for the measurement of gamma-ray energies and emission rates of radionuclides and the assay of radioactivity. Is applicable to scintillation detector systems based on inorganic scintillators for photon measurements.
  • IEC 61468
    Applies to in-core neutron detectors and instrumentation, which are designed for purposes important to safety, such as protection, control and information. Gives requirements, recommendations and guidance on selection of the type and characteristics of self powered neutron detectors used in(...)
  • IEC 61472
    Describes a method for calculating the minimum approach distances for live working, at maximum voltages between 72,5 kV and 800 kV. This standard addresses system overvoltages and the working air distances or tool insulation between parts and/or workers at different electric potentials.
  • IEC 61477
    Gives the minimum requirements relative to specification, manufacture, selection, application and maintenance of tools, devices and equipment for live working. It provides the type of information which is useful to skilled persons in order to make the use of tools, devices and equipment safer.
  • IEC 61478
    Is applicable to fully insulating spliced or hook ladders with extension or having a combination of insulating and conductive sections and used for live working on a.c. or d.c. electrical installations at 1 000 V and above for a.c. and 1 500 V and above for d.c. This standard concerns only(...)
  • IEC 61479
    Is applicable to flexible insulating covers (line hoses) for the protection of workers from accidental contact with live or earthed electrical conductors and for the avoidance of short circuits during live working.
  • IEC 61481
    Is applicable to portable phase comparators with or without a built-in power source to be used on electrical systems for voltages from 1 kV to 36 kV a.c. and frequencies from 50 Hz to 60 Hz. This standard is applicable to two-pole phase comparators having a connecting lead between them,(...)
  • IEC 61482-1-1
    Specifies test methods to measure the arc thermal performance value of materials intended for use in heat- and flame-resistant clothing for workers exposed to the thermal effects of electric arcs and the function of garments using these materials.
  • IEC 61482-1-2
    This part of IEC 61482 specifies methods to test material and garments intended for use in heat- and flame-resistant clothing for workers exposed to electric arcs. In contrast to the test methods in IEC 61482-1-1 a directed and constrained electric arc in a low voltage circuit is used to(...)
  • IEC 61482-2
    Applicable to protective clothing used in work if there is an electric arc hazard. Specifies requirements and test methods applicable to materials and garments for protective clothing for electrical workers against the thermal hazards of an electric arc based on: relevant general properties of(...)
  • IEC 61496-1
    Specifies general requirements for the design, construction and testing of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety related system.
  • IEC 61496-2
    Specifies requirements for the design, construction and testing of electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety-related system, employing active opto-electronic protective devices (AOPDs) for the sensing function.
  • IEC 61496-3
    Specifies additional requirements for the design, construction and testing of non-contact electro-sensitive protective equipment (ESPE) designed specifically to detect persons as part of a safety related system, employing active opto-electronic protective devices responsive to diffuse(...)
  • IEC 61500
    IEC 61500:2009 establishes requirements for data communication which is used in systems performing category A functions in nuclear power plants. It covers also interface requirements for data communication of equipment performing category A functions with other systems including those(...)
  • IEC 61501
    Describes the principles, the terminology, the characteristics, the requirements and the testing methods related to instrumentation and measurement of the neutron fluence rate using mean square voltage techniques for nuclear reactor control.
  • IEC 61502
    Applies to systems used for monitoring the vibratory behaviour of the internal structures of pressurized water reactors (core barrel, thermal shield, upper and lower core support, etc.) and fuel assemblies on the basis of neutron fluctuations observed outside the vessel and vessel vibrations.(...)
  • IEC 61508-1
    Covers those aspects to be considered when electrical/electronic/programmable electronic (E/E/PE) systems are used to carry out safety functions
  • IEC 61508-2
    IEC 61508-2:2010 applies to any safety-related system, as defined by IEC 61508-1, that contains at least: one electrical, electronic or programmable electronic element; applies to all elements within an E/E/PE safety-related system; specifies how to refine the E/E/PE system safety requirements(...)
  • IEC 61508-3
    IEC 61508-3:2010 applies to any software forming part of a safety-related system or used to develop a safety-related system within the scope of IEC 61508-1 and IEC 61508-2; provides specific requirements applicable to support tools used to develop and configure a safety-related system within(...)
  • IEC 61508-4
    IEC 61508-4:2010 contains the definitions and explanation of terms that are used in parts 1 to 7 of the IEC 61508 series of standards. The definitions are grouped under general headings so that related terms can be understood within the context of each other. However, it should be noted that(...)
  • IEC 61508-5
    IEC 61508-5:2010 provides information on the underlying concepts of risk and the relationship of risk to safety integrity (see Annex A); a number of methods that will enable the safety integrity levels for the E/E/PE safety-related systems to be determined (see Annexes C, D, E, F and G). The(...)
  • IEC 61508-6
    IEC 61508-6:2010 contains information and guidelines on IEC 61508-2 and IEC 61508 3. Annex A gives a brief overview of the requirements of IEC 61508-2 and IEC 61508-3 and sets out the functional steps in their application. Annex B gives an example technique for calculating the probabilities of(...)

X