Get our free email newsletter

Induction: What it means to ESD

Associate Professor Neils Jonassen authored a bi-monthly static column that appeared in Compliance Engineering Magazine. The series explored charging, ionization, explosions, and other ESD related topics. The ESD Association, working with IN Compliance Magazine is re-publishing this series as the articles offer timeless insight into the field of electrostatics.

Professor Jonassen was a member of the ESD Association from 1983-2006. He received the ESD Association Outstanding Contribution Award in 1989 and authored technical papers, books and technical reports. He is remembered for his contributions to the understanding of Electrostatic control, and in his memory we reprise “Mr. Static”.

~ The ESD Association

- Partner Content -

A Dash of Maxwell’s: A Maxwell’s Equations Primer – Part One

Solving Maxwell’s Equations for real-life situations, like predicting the RF emissions from a cell tower, requires more mathematical horsepower than any individual mind can muster. These equations don’t give the scientist or engineer just insight, they are literally the answer to everything RF.

Reprinted with permission from: Compliance Engineering Magazine, Mr. Static Column Copyright © UBM Cannon

Can an uncharged, insulated conductor have a voltage of, say, 1000 V? Can a charged, insulated conductor have zero voltage? The answer common to both of these seemingly paradoxical questions is yes, if we’re dealing with the concept of induction. In this article, we’ll discuss induction in its two forms and examine a series of practical examples which point to the fact that induction is a subject relevant to and worthy of ESD investigation.

Types of Induction

In the world of electricity we have two kinds of induction: electromagnetic induction and electrostatic induction.

Electromagnetic Induction

- From Our Sponsors -

Electromagnetic induction is the phenomenon that a time-varying magnetic field creates, or rather induces—an electromotive force expressed in Faraday’s law of induction as


where F is the magnetic flux through a surface and Ei is the electromotive force induced along a curve bordering the surface. Electromagnetic induction is the basis for all (or nearly all) electrical power production.

Electrostatic Induction

Electrostatic induction describes the static effect of an electric field on a conductor.


An insulated, uncharged conductor B is in the field from a positively charged insulator A (see Figure 1). The field from A will cause electrons in B to move to the side of B that faces A. These electrons make up the bound induced charge. This charge cannot be removed as long as B is in the field from A. The corresponding excess positive charge—the free induced charge—is located on the opposite side of B. But the total charge on B is still zero, as is the field inside B. The free induced charge (positive) creates an electric field outside of B, with the field lines eventually terminating on some grounded object. If this field is integrated from B to a ground point, we will get a positive figure, which, by definition, is the voltage of B. Thus we have an uncharged conductor with a positive voltage.



Figure 1: Insulated conductor in the field from a charged insulator.

In Figure 2 we have the same situation as in Figure 1, except that now the conductor is grounded. Consequently the voltage of B is zero. But because B still has the negative, bound induced charge, we have a negatively charged conductor with zero voltage. If the ground connection is broken, and B is moved away from the neighborhood of A (in an insulated way), B will still have its negative charge, giving B a negative voltage. We describe this process as B having been charged by induction. Let’s illustrate the first part of this scenario with a practical example.



Figure 2: Grounded conductor in the field from a charged insulator

Figure 3 shows an operator holding a piece of positively charged insulative material. The operator is standing on an insulating floor covering backed by a grounded layer that is more-or-less conductive. The charge from the material will, by induction, bind a negative charge on the operator. Since the operator has no excess charge, a positive charge of the same numerical magnitude as the negative charge will cause the operator to have a positive voltage. The field lines from the operator’s positive charge will run through the floor covering to the grounded underlayer. That is, at least some of them will go there. Other field lines may go to the walls of the room.

The field distribution suggested in Figure 3 is somewhat misleading. The major part of the electric flux (i.e., the number of field lines) from the operator will run from the undersides of the operator’s feet through the floor covering to a conductive, grounded layer. (Remembering that field lines have no problem penetrating insulating materials is important here to ensure induced charges and their effects are tracked.) Therefore, the situation shown in Figure 3 is that of an uncharged person being charged to a positive voltage just by virtue of being near a charged piece of material.




Figure 3: Insulated operator handling a charged piece of insulative material.


The question now is, why might this pose a greater risk (or nuisance) than just having the charged piece of material around in the absence of insulated conductors? The reason is as follows: any direct discharge in the field from the material’s surface will be a low energy-density discharge (corona or brush), which normally will have only minor harmful effects. But if the charged material binds by induction a charge of just 1 mC on the operator, the operator will carry about 5000 V and be able to dissipate an energy in his environment of about 2 mJ, or 10 times the minimum ignition energy for most mixtures of organic vapors with atmospheric air. Of course if the operator drops the material and just walks away, the operator is uncharged, has no voltage, and is considered to be safe. But if the operator accidentally gets grounded during the work, he loses the free charge and may walk away with an excess (negative) charge, carrying the risk for an energetic spark discharge.

A practical example of dangerous induction charging (Figure 4) is an operator pouring powder (resin) from a plastic-lined bag into a tank containing explosive vapors (acetone). The operator, who is not grounded, is uncharged during the entire operation. The resin charges the plastic lining of the bag, and the field from the bag induces a charge on the operator and gives him a voltage. When the operator accidentally touches the tank, a spark discharge occurs, resulting in an explosion that hurts the operator badly.




Figure 4: Ungrounded operator handling insulative materials in an unsafe environment.

Potential Harmful Effects for the Electronics Industry

There are also many examples of electrostatic induction’s harmful effects in the electronics arena. A simple example is that of an ungrounded operator being near a piece of charged material of any kind. The operator will, by induction, be charged to a voltage (although the operator’s total charge may be zero), and if this person then touches a grounded component the resulting current pulse may destroy the component.

But let’s look at a somewhat more-complicated example (see Figure 5). Here we have a positively charged object—an insulator in this case (the field lines are not perpendicular to the surface). Near this object is an electronic component or device. The field from the charged object binds by induction a negative charge on an insulated, conductive part (a) of the component. The total charge on (a) is zero; thus, a positive charge numerically equal to the negative one resides on the other side of (a) and creates a field through the insulative, or rather, dielectric, layer, to the grounded part of the component (c). The critical part in this situation is the field through the dielectric. If this field is high enough, a breakdown happens. This is known as field-induced damage.




Figure 5: Field-induced damage where (a) is an insulated, conductive part of the component, (b) is an insulative (dielectric) layer, and (c) is a ground (conductive) part.


Among the ESD damage models, the field-induced model is still viewed with skepticism by some people in the electronics industry. They don’t believe that fields can induce high-enough voltages in components and circuits to cause breakdown. But with dielectric layers getting thinner and thinner, and, consequently, with field strengths at the edges of the conductive layers getting higher, breakdown does become more and more likely.


The concept of electrostatic induction may seem somewhat elusive. On a more scholarly level it demonstrates that the concept of electric fields is by far more fundamental, and often much more useful, than the more-earthbound concept of voltage. The field from a charged body may cause another body to have a voltage, although it has no charge, and the field from a charged body may cause another body to have a charge, although it has no voltage.

Hopefully I have demonstrated that although the concept of induction may look like a good target for an academic exercise, sometimes it also has practical and damaging consequences that make it an obvious topic of consideration for any ESD (or, at least, electrostatic) investigation. favicon



Niels Jonassen, MSc, DSc

worked for 40 years at the Technical University of Denmark, where he conducted classes in electromagnetism, static and atmospheric electricity, airborne radioactivity, and indoor climate. After retiring, he divided his time among the laboratory, his home, and Thailand, writing on static electricity topics and pursuing cooking classes. Mr. Jonassen passed away in 2006.



Related Articles

Digital Sponsors

Become a Sponsor

Discover new products, review technical whitepapers, read the latest compliance news, trending engineering news, and weekly recall alerts.

Get our email updates

What's New

- From Our Sponsors -

Sign up for the In Compliance Email Newsletter

Discover new products, review technical whitepapers, read the latest compliance news, trending engineering news, and weekly recall alerts.