Glossary

AJAX progress indicator
Search: (clear)
  • i

  • IEC 60839-7-11
    Specifies the requirements for standard interfaces between the Public Switched Telephone Network (PSTN) and alarm system transceivers. Specifies a 1 200 baud interface using ITU-T Recommendation V.23.
  • IEC 60839-7-12
    Specifies the requirements for standard interfaces between the alarm system transceivers and transmission network where both form part of a dedicated channel alarm transmission system as defined in IEC 60839-5-4.
  • IEC 60839-7-2
    Specifies a common application layer protocol (message structure, formats and transmission procedures) to be used at standard interfaces in alarm transmission systems. Should be used at all such interfaces where equipment from one supplier is intended to inter-work with equipment from other(...)
  • IEC 60839-7-20
    Specifies the requirements for standard interfaces between the terminal transceiver of an alarm transmission system and the annunciation equipment. Employs signalling in accordance with ITU-T Recommendation V.24/V.28.
  • IEC 60839-7-3
    Specifies the data link layer message structure, formats and transmission procedures which should be used at standard serial data interfaces in alarm transmission systems where the transmission network employed does not offer a standard protocol.
  • IEC 60839-7-4
    Specifies the transport layer message structure, formats and transmission procedures to be used at standard interfaces in alarm transmission systems.
  • IEC 60839-7-5
    Specifies the requirements for standard interfaces using a two-wire connection employing ISO/IEC 8482 signalling for use between the control and indicating equipment of an alarm system and one or more alarm system transceivers connected to alarm transmission systems.
  • IEC 60839-7-6
    Specifies the requirements for standard interfaces employing ITU-T V.24/V.28 signalling for communications between the control and indicating equipment of an alarm system and transmission equipment used for remote communications, where the transmission equipment is general purpose equipment.(...)
  • IEC 60839-7-7
    Specifies the requirements for standard interfaces between the control and indicating equipment (CIE) of an alarm system and an alarm system transceiver where the alarm system transceiver is intended to plug into a standard space inside the CIE of the alarm system.
  • IEC 60846-1
    Specifies the design requirements and the performance characteristics of dose equivalent (rate) meters intended for the determination of ambient dose equivalent (rate) and directional dose equivalent (rate) as defined in ICRU Report 47.
  • IEC 60846-2
    Applies to portable or transportable dose equivalent (rate) meters and/or monitors for the measurement of ambient and/or directional dose equivalent (rate) from external beta, X and gamma radiation during emergency situations.
  • IEC 60855-1
    Applicable to insulating foam-filled tubes and solid rods, of a circular cross-section, made of synthetic materials and intended to be used for the manufacture and construction of tools and equipment for carrying out live work on electrical systems operating at voltages above 1 kV.
  • IEC 60860
    Applies to equipment intended to detect ionizing radiation from, and provide warning of, a criticality accident. Specifies the general characteristics, operating characteristics, electrical, mechanical, safety and environmental characteristics, test procedures and documentation.
  • IEC 60861
    Defines technical requirements for equipment for monitoring of alpha-, beta- or gamma-emitting radionuclides in liquid effluents and surface waters, provides general guidance as to the possible detection capability of such equipment and indicates when and where its uses may be practicable.
  • IEC 60880
    Provides requirements for the software of computer-based instrumentation and control (I&C) systems of nuclear power plants performing functions of safety category A as defined by IEC 61226. Provides requirements for the purpose of achieving highly reliable software.
  • IEC 60891
    IEC 60891:2009 defines procedures to be followed for temperature and irradiance corrections to the measured I-V (current-voltage) characteristics of photovoltaic devices. It also defines the procedures used to determine factors relevant for these corrections.
  • IEC 60895
    Applicable to conductive clothing, either assembled from component parts or forming a single complete clothing, worn by (electrically) skilled persons during live working (especially bare-hand working) at a nominal power system voltage up to 800 kV a.c. and ±600 kV d.c. It is applicable to(...)
  • IEC 60900
    Applicable to insulated and insulating hand tools used for working live or close to live parts at nominal voltages up to 1 000 V a.c. and 1 500 V d.c. This third edition cancels and replaces the second edition, published in 2004.
  • IEC 60903
    This standard is applicable to: - insulating gloves and mitts which should normally be used in conjunction with leather protector gloves worn over the insulating gloves to provide mechanical protection; - insulating gloves and mitts usable without over-gloves for mechanical protection.
  • IEC 60904-1
    Describes procedures for the measurement of current-voltage characteristics of photovoltaic devices in natural or simulated sunlight. Lays down basic requirements for the measurement, defines procedures for different measuring techniques in use and shows practices for minimising measurement(...)
  • IEC 60904-10
    IEC 60904-10:2009 describes procedures used to determine the degree of linearity of any photovoltaic device parameter with respect to a test parameter. It is primarily intended for use by calibration laboratories, module manufacturers and system designers.
  • IEC 60904-2
    Gives requirements for the classification, selection, packaging, marking, calibration and care of reference solar devices. Covers solar reference devices used to determine the electrical performance of solar cells, modules and arrays under natural and simulated sunlight.
  • IEC 60904-3
    IEC 60904-3:2008 describes basic measurement principles for determining the electrical output of PV devices. The principles given in this standard are designed to relate the performance rating of PV devices to a common reference terrestrial solar spectral irradiance distribution.
  • IEC 60904-4
    IEC 60904-4:2009 sets the requirements for calibration procedures intended to establish the traceability of photovoltaic reference solar devices to SI units as required by IEC 60904-2. Applies to photovoltaic (PV) reference solar devices that are used to measure the irradiance of natural or(...)
  • IEC 60904-5
    IEC 60904-5:2011 describes the preferred method for determining the equivalent cell temperature (ECT) of PV devices (cells, modules and arrays of one type of module), for the purposes of comparing their thermal characteristics, determining NOCT (nominal operating cell temperature) and(...)
  • IEC 60904-7
    IEC 60904-7:2008 describes the procedure for correcting the bias error introduced in the testing of a photovoltaic device, caused by the mismatch between the test spectrum and the reference spectrum and by the mismatch between the spectral responses (SR) of the reference cell and of the test(...)
  • IEC 60904-8
    Gives guidance for the measurement of the relative spectral response of both linear and non-linear photovoltaic devices.
  • IEC 60904-9
    Defines classifications of solar simulators for use in indoor measurements of terrestrial photovoltaic devices; solar simulators are classified as A, B or C for each of the three categories based on criteria of spectral distribution match, irradiance non-uniformity on the test plane and(...)
  • IEC 60910
    Gives recommendations on the data to be measured to enable an operator to diagnose developing deviations from normal functioning so as to take corrective action at an early stage.
  • IEC 60911
    Defines requirements for additional instrumentation to measure coolant parameters, which are of interest when abnormal conditions arise with either one or two phases of coolant or with gas included in the reactor vessel.

X